Your Jetson camera streams cleanly for a few minutes, then collapses under a wall of fence ioctl errors. The console shows SYNC_IOC_FENCE_INFO ioctl failed with 9, Argus raises BadParameter inside copyToNvBuffer(), and NvRmChannelSubmit reports error 22 — the signature of a multimedia API tree built against one L4T release and run against another. This guide is for engineers integrating a MIPI CSI camera on a Jetson module who built or copied those sources by hand. You will decode each error number, confirm the release mismatch in minutes, and choose between the two clean exits: rebuild the whole capture stack on one JetPack version, or move the camera off the Argus stack entirely.
The error set, decoded
Four console lines identify this failure, and every one of them is a number you can look up:
-
SYNC_IOC_FENCE_INFO ioctl failed with 9— errno 9 is EBADF, a bad file descriptor. The sample hands the kernel a sync-file fence descriptor the kernel does not recognise, so the ioctl rejects the descriptor itself. -
Error BadParameter: Unable to get fd, raised insrc/eglstream/ImageImpl.cpp, functioncopyToNvBuffer(), line 467 — the Argus EGLStream layer cannot return the NvBuffer file descriptor to the application. BadParameter from Argus is a generic refusal; where it comes from decides the cause. The same message over a remote desktop session is an EGL problem rather than a version one, and that case is covered in Argus BadParameter frameconsumer errors over remote desktop. -
NvRmChannelSubmit: NvError_IoctlFailed with error code 22— errno 22 is EINVAL, an invalid argument. The channel submit carries a syncpoint or fence structure the running kernel will not parse. -
NvRmPrivFlush: NvRmChannelSubmit failed (err = 196623, SyncPointIdx = 390, SyncPointValue = 0), with afence_set_namefailure behind it — the flush of the same channel, the syncpoint stuck at zero because the submit never completed.
Read together, the four lines say one thing: user space and the kernel disagree about a fence object. That disagreement is a build problem, not a signal problem.
Why a mixed release breaks the fence path
The samples under /usr/src/jetson_multimedia_api link against Argus client libraries and NvBuffer helpers that are rebuilt for every L4T release. Those libraries pass file descriptors — sync-file fences, buffer descriptors — across the user-kernel boundary through ioctls whose argument layouts are internal to each release. A tree carried over from a neighbouring release produces descriptors that are well-formed for one side and meaningless for the other, which is exactly what EBADF and EINVAL report.
The runtime itself — kernel, nvargus-daemon, the client libraries — comes from the flash image. Only the samples are yours to build, which is why it is always the sample build that gets 'fixed' by copying, and always the runtime that refuses it.
The stack runs until the first operation exercises the changed interface, so a hand-copied tree streams for a while and then fails minutes in. The failure is delayed, not absent.
The sources are part of the platform release, not a portable package. SDK Manager installs them with the other SDK components, and afterwards the tree sits at /usr/src/jetson_multimedia_api on the module. On the JetPack 4.4 cycle, R32.4.0 was a limited pre-release with no sample package published, R32.4.2 is the formal release SDK Manager installs, and R32.4.3 followed as the next production release. A request for the R32.4.0 package has one honest answer: it does not exist, so the stack aligns upward, never downward.
The rule: every layer on one L4T release
Break any one of those equalities and the build is unsupported, however cleanly it compiles. The repair is never to copy a tree across releases; it is to rebuild each part from the one release the module runs. The same discipline governs the rest of the Jetson software stack — a JetPack and VPI version mismatch on a GMSL camera fails one layer up, in the vision libraries, for the same reason.
Test the causes in order of probability
Work down this list and stop at the first test that fails:
-
Mixed-release multimedia API tree — most likely. The signature is minutes of clean video, then the fence error set, reproducibly. Write down the L4T release the module runs — SDK Manager lists it for the installed JetPack, and the release notes map JetPack versions to L4T — then trace where the tree under
/usr/src/jetson_multimedia_apicame from. A hand copy from another module or release fails the test on the spot. -
A wedged Argus daemon. Restart
nvargus-daemonand re-run the capture. If the same errors return within the first minutes, the daemon was a symptom, not the cause. - Camera driver built against another kernel. An out-of-tree MIPI driver compiled for a different L4T kernel can probe, stream, and still destabilise the capture path. Read the driver's probe and stream-on logs before the fence failures start; probe-time failures such as camera driver probe error -34 belong here. Rebuild the driver against the running kernel's headers.
- CSI signal integrity — least likely when video is clean first. Lane problems corrupt frames and drop streams sporadically; they do not produce a repeatable errno set at a fixed point in the run. The distinguishing signs are in CSI lane alignment errors and intermittent capture failures.
Worked example: Jetson NX on JetPack 4.4 with an R32.4.0 driver
Inputs, from the integration case this failure pattern comes from:
- Module: a Jetson NX.
- Installed stack: JetPack 4.4, whose formal release is L4T R32.4.2.
- Camera: a third-party MIPI CSI module, driver and tuning validated on R32.4.0 only.
- Attempted fix: the
jetson_multimedia_apitree from R32.4.2, copied by hand and built into the R32.4.0-based set-up. - Outcome: the camera streams for a while, then the fence error set above kills capture.
Decode the numbers before touching hardware:
- 9 and 22 are Linux errno values: EBADF, bad file descriptor, and EINVAL, invalid argument. Both report the same condition — the kernel refuses an object the user-space library handed it.
- 196623 converts to hex as 3 × 65536 + 15 = 196608 + 15, so err = 0x3000F. SyncPointIdx 390 with SyncPointValue 0 says the syncpoint never advanced: the submit was refused, and the flush reports a capture that never happened.
Apply the rule: kernel R32.4.2, daemon R32.4.2, multimedia API tree carried across from a neighbouring release, camera driver lineage R32.4.0. Two of the four equalities are broken.
Decision: an all-R32.4.0 stack cannot be assembled — R32.4.0 shipped no multimedia API package — so align upward. Port the camera driver to R32.4.2 (or R32.4.3 once that is the production release you flash), install the tree SDK Manager ships with the same release, and rebuild both on the module. If the camera vendor cannot supply a driver for a formal release, replace the camera rather than ship a mixed build.
Align the stack, step by step
- Fix the JetPack version for the project and write down its L4T release before flashing anything.
- Flash with SDK Manager with the multimedia API component included, then confirm
/usr/src/jetson_multimedia_apiexists on the module. - Delete every hand-copied tree and build the samples from the installed one, on the module itself.
- Rebuild the camera driver against the same release — from source you own, or the vendor's build for that L4T.
- Restart
nvargus-daemon, then soak-test well past the point where the fence errors used to appear. Thirty minutes of continuous capture is a sensible floor for a stack that failed at minute five. - Freeze the JetPack version for the line. Every later L4T upgrade is a full rebuild of driver and samples; check the camera vendor's supported-release matrix before starting one.
When the usual answer is wrong: get off the Argus stack
The rebuild path assumes the camera vendor supports the L4T release you run. When their matrix stops at a pre-release, no rebuild makes the MIPI path supportable, and every JetPack upgrade re-opens the same failure.
Industrial USB3 and GigE cameras never touch the multimedia API. They stream through their own host-side stack — a GenTL producer for machine-vision cameras, a class driver for UVC devices — so nvargus-daemon and the Argus samples are simply not in the path. On a Jetson NX class module a GigE link carries 1 Gb/s of line rate and a USB3 port 5 Gb/s, so size resolution and frame rate against the port you have free.
The LS-CMR-0166 is a 12 MP USB3 area scan camera with an IMX226 sensor, 1/1.7-inch rolling shutter, 30 fps output and 4000 × 3000 resolution. Where the camera mounts inside an enclosure, board-level cameras such as the LS-BCM-0020 — a 6.3 MP IMX178 board-level camera with 18 fps output over GigE — build in without a housing.
- Sensor format
- 1/1.7"
- Interface
- USB3
- Resolution
- 12 MP
- Shutter
- Rolling
- Sensor format
- 1/1.8"
- Lens mount
- CS-mount
- Resolution
- 6-10 MP
- Shutter
- Rolling
Filter area scan cameras by interface and resolution in the camera finder, or start at the camera step of the system configurator and let it carry the lens and light. More camera bring-up guides sit under the cameras topic.
Checklist before your next build
- One JetPack version, and its L4T release, written down for the project before the first flash.
- The multimedia API tree installed by SDK Manager for that release — never copied between releases or between modules.
- The camera driver built against that release's kernel, with the vendor's supported-release matrix on file.
-
nvargus-daemonrestarted after every rebuild, before the soak test. - A soak test that runs well past the minute count where the fence errors last appeared.
- A USB3 or GigE camera on the shortlist for any new design whose MIPI vendor supports only pre-release L4T versions.
If the decision is to leave MIPI, the finder and configurator above size the replacement in minutes. For anything unusual, send us the details — working distance, field of view, frame rate — and we will pick the camera and lens with you.
Questions
Where do the jetson_multimedia_api sources for a specific release come from?
From SDK Manager, as an SDK component of that release: after installation the tree sits at /usr/src/jetson_multimedia_api on the module. There is no standalone package to fetch for an arbitrary version, and pre-release versions published none at all — R32.4.0 on the JetPack 4.4 cycle is the classic case. If SDK Manager does not list a release, its multimedia API tree was never published, and no deb exists to install by hand.
Can I copy a multimedia API tree from one L4T release into another?
It compiles and often streams, which is what makes the trap expensive. The fence and NvBuffer interfaces the samples use are internal to each release, so a mixed build fails at runtime — typically minutes into a run — with SYNC_IOC_FENCE_INFO error 9 and NvRmChannelSubmit error 22. Treat any by-hand build as unproven until it has soaked well past the point where the errors used to appear.
Does restarting nvargus-daemon fix the fence errors?
It recovers a wedged daemon and buys another run, but it does not repair a mixed-release build: the same error set returns on the next capture. Use the restart as a diagnostic — clean video for a few minutes followed by the same failures points at the stack, not the daemon. Restart it after every rebuild so the soak test starts from a clean process.
My camera vendor only supports an old L4T release. What should I do?
Take the cheapest path that survives upgrades: first ask the vendor for a driver build against the formal release you run (R32.4.2 on the JetPack 4.4 cycle, with R32.4.3 following); if they cannot supply one, port the driver yourself against that kernel; if you do not own the driver source, replace the module with a USB3 or GigE industrial camera. The last option is the only one that does not relive this failure at the next JetPack upgrade.
Do USB3 and GigE machine-vision cameras need the multimedia API?
No. nvargus-daemon, the EGLStream path and the NvBuffer fences exist for MIPI CSI cameras. USB3 and GigE industrial cameras stream through their own host-side stack — a GenTL producer or a USB class driver — so an L4T update cannot break them the way it breaks a hand-built Argus sample. Your own application software is the only part you rebuild after an upgrade.

