System designTroubleshooting

Control transfer resource temporarily unavailable on a depth camera

What 'Resource temporarily unavailable' control-transfer warnings mean while a depth camera streams, and the cable, hub, port and power checks that stop them.

LumaSpec Vision12 min read Share on LinkedIn

On this page 9 sections
  1. 01What the warning actually says
  2. 02Why the flood starts when the streams start
  3. 03Worked example: payload for six streams at 640 × 480, 30 fps
  4. 04Likely causes, in order of probability
  5. 05Fix it in this order
  6. 06When the usual answers do not work
  7. 07When it really is the camera
  8. 08Prevent it on the next install
  9. 09Questions

Your depth camera enumerates, the streams publish, frames arrive — and the console keeps printing control-transfer warnings that end in Resource temporarily unavailable. Nothing crashes, but the warnings never stop. This guide is for anyone running a multi-stream depth camera — depth, two IR streams, color and IMU — over USB 3 on a Linux host. You will read the warning precisely, budget the link's payload with real arithmetic, and work the causes in field order: hub hops, cable quality, port wiring, power, controller contention. The conclusion up front: a six-stream profile carries about 64 MB/s, comfortably inside USB 3.x, so the fix is almost always the physical path, not your code.

What the warning actually says

One line carries the whole diagnosis:

control_transfer returned error, index: 768, error: Resource temporarily unavailable, number: 11

The trailing number is the operating system's error code. Code 11 is EAGAIN, 'Resource temporarily unavailable': the request was well formed, but the endpoint could not service it at that moment. The index identifies which of the camera's commands failed; the same index repeating means the wrapper polls the same periodic read — status, timestamps — and hits the same wall each time. The line comes from the library's transfer layer (messenger-libusb.cpp), not from your node's code, so there is nothing to fix in your program.

Read the pattern, not the line count. A burst of a few warnings while profiles start, then silence, is normal spin-up. Warnings repeating every few hundred milliseconds during steady streaming are the fault signature. Companion lines that report a status value 'is not valid' are the same failed read seen by the status reader — they are not separate faults.

Why the flood starts when the streams start

A depth camera exposes two kinds of USB traffic. Image data rides bulk endpoints; commands and periodic status reads ride the default control endpoint. While the link is idle, control requests complete trivially, so the camera can pass enumeration and even a preview without a single warning.

Start the full profile and the picture changes. Six streams push tens of megabytes per second through the same cable, hub and host controller that must also carry the small control reads. On a clean link both coexist without complaint. On a degraded link — a marginal cable, a hub hop, a tired port — the bulk traffic retries packets and backs up buffers, and the periodic control read is the first request to bounce. That is why EAGAIN floods appear exactly when streams run: the streams are the stress test that exposes the path, not the cause of the fault.

The same budget logic explains the industrial cousins: USB3 Vision transfer errors trace to bandwidth and buffer budgets in the same way, and the general method is written up in the camera bandwidth budget.

Worked example: payload for six streams at 640 × 480, 30 fps

Inputs, as configured in the case that produced this flood: depth at 640 × 480, 30 fps, Z16; two IR streams at 640 × 480, 30 fps, Y8; color at 640 × 480, 30 fps, RGB8; gyro at 200 Hz; accelerometer at 100 Hz. Depth-to-color alignment, where enabled, computes the aligned image on the host from streams you already receive, so it costs CPU, not USB payload.

The rule: each stream's payload is its pixel count times its bytes per pixel times its frame rate, and the link carries the sum of all streams.

payload = width × height × bytes per pixel × frame rate total payload = Σ payload over all streams
Stream Format Bytes per frame Payload
Depth Z16 640 × 480 × 2 B = 614,400 B 18.4 MB/s
IR 1 Y8 640 × 480 × 1 B = 307,200 B 9.2 MB/s
IR 2 Y8 640 × 480 × 1 B = 307,200 B 9.2 MB/s
Color RGB8 640 × 480 × 3 B = 921,600 B 27.6 MB/s
Gyro + accel — a few dozen B per sample < 0.01 MB/s

The arithmetic: depth is 614,400 B × 30 = 18,432,000 B/s ≈ 18.4 MB/s. Each IR stream is 307,200 B × 30 = 9,216,000 B/s ≈ 9.2 MB/s, so the pair adds 18.4 MB/s. Color is 921,600 B × 30 = 27,648,000 B/s ≈ 27.6 MB/s. The IMU pair is about 300 samples/s of a few dozen bytes, under 0.01 MB/s. The total is 18.4 + 18.4 + 27.6 = 64.4 MB/s ≈ 64 MB/s, and 64.4 MB/s × 8 ≈ 515 Mbit/s of payload.

Capacity check: a USB 3.x Gen 1 port signals at 5 Gbit/s; 8b/10b line coding leaves 4 Gbit/s, and protocol overhead brings sustained bulk throughput on a clean link to roughly 400 MB/s — about 3.2 Gbit/s. That figure is an estimate, but measured bulk numbers on healthy hosts sit close to it.

Result and decision: 515 Mbit/s is about one sixth of that capacity, so bandwidth is not the fault at this profile and cutting resolution is the wrong first move. The thresholds that matter: keep the total payload on one host controller under about half its practical capacity, call it 200 MB/s, whenever anything else streams there. What moves you across that line: 1280 × 720 at 30 fps triples the pixel count to about 193 MB/s; a second camera at this profile adds another 64 MB/s; dropping 30 to 15 fps halves the total; disabling color is the biggest single cut at 27.6 MB/s. At 64 MB/s the streams fit, so a steady EAGAIN flood points at the physical path — hub, cable, port or power.

Likely causes, in order of probability

Work the table top to bottom; the first row that tests clean is your answer.

# Cause Test Confirmed by
1 A hub hop: dock, monitor hub or front-panel header Count the hub levels in the device path the SDK prints; inspect the tree with lsusb -t The path runs through one or more hubs, or the speed reads below 5000M
2 A cable not up to USB 3 duty: too long, worn, or USB 2 only Swap in a short, shielded USB 3 cable and run the full profile for five minutes The flood stops the moment the cable changes
3 A front-panel port, or two ports sharing one controller Move to a rear motherboard or host root port and compare the bus layout in lsusb -t The warnings vanish on the other root port
4 Power budget on a bus-powered hub Read the kernel log (dmesg) during a run Repeated reset and disconnect lines, then re-enumeration
5 Another device sharing the controller Sum the payloads on that controller as in the worked example Warnings return when the second stream starts
6 The camera board itself Depth-only profile on a root port, then the same minimal profile on a second PC Warnings persist from the first frame on both hosts

Row 1 is where most hunts end, and it has its own pages: a camera that enumerates as a hub is diagnosed in Camera enumerates as a generic USB hub, and the same hub failure pattern is why raw depth streams refuse to start on a USB hub.

Rows 2 to 4 are cable and power problems: USB cable length limits for 3D cameras gives the distance each cable class sustains, the swap procedure is laid out in the USB link checks after a cable swap, and a link that passes idle traffic but dies under recording load is exactly the case in the USB extension cable that fails only when recording the depth stream. Reset-and-reconnect lines in row 4 point at power — the signature behind a USB camera that connects then disconnects.

Fix it in this order

  1. Move to a root port. Rear motherboard or host port, camera plugged in directly, nothing between. On its own, this clears most cases.
  2. Swap the cable. Shielded USB 3, at most 3 m passive, with a locking connector or real strain relief; on a moving axis use a drag-chain-rated cable. The 3 m USB3.0 high-flex camera cable is built for exactly this duty, and the camera cables range covers other lengths and connectors.
Cables3 m USB3.0 camera cable, high-flex (drag chain) (LS-CBL-0219)LS-CBL-0219$62.00View partBuild a system with it
  1. Verify the negotiated speed. lsusb -t should show 5000M for the camera. A 480M line means the path is USB 2 somewhere — cable, port or hub — and that is a different failure: see why a USB 2.0 port fails the depth stream's bandwidth check. A log line such as Device USB type: 3.2 shows SuperSpeed negotiation; it does not certify the cable, because a marginal cable can negotiate full speed and still drop packets under load.
  2. Soak test. Run the full production profile for five minutes. Zero repeated EAGAIN lines after the first seconds and no reset lines in the kernel log is a pass.
  3. Trim streams only if the controller is shared. Each disabled IR stream saves 9.2 MB/s, disabling color saves 27.6 MB/s, and halving 30 to 15 fps halves the total. Keep the controller's total under about 200 MB/s.
  4. Update firmware last. Bring the camera to current firmware with the vendor's documented updater, re-test, and only then treat the camera as the suspect.

One habit to keep: pin the camera to the port that works. Most wrappers accept a serial number or USB port selector, so a replug cannot quietly route the camera back through the hub.

When the usual answers do not work

  • You cut the resolution and the flood stays. The arithmetic says 64 MB/s fits, so resolution was never the wall. Go back to the path: port, cable, hub.
  • You added a powered hub. A hub adds a hop, a second power negotiation and another pair of connectors. Hubs belong in the test plan, not the fix; removal is the fix.
  • You switched periodic reads off and the log went quiet. Disabling hardware time sync — the wrapper's global_time_enabled switch, for example — hides the messenger, not the fault. The degraded link is still there, the flood returns under load, and you have lost hardware timestamps.
  • You see warnings only at start-up. That is the normal spin-up signature. Judge the link by a clean minute after the streams settle.

When it really is the camera

Give the camera its last chance under ideal conditions: a root port, a known-good USB 3 cable of 3 m or less, no hub, and a depth-only profile of about 18.4 MB/s. If EAGAIN warnings still repeat from the first frame, run the identical minimal profile on a second computer.

Warnings persisting on both hosts point at the camera's USB transceiver or board; replace or service it. The 3D sensors range is where to pick a replacement, and the camera finder filters depth, ToF and structured-light models by interface and resolution. A clean run on the second PC clears the camera and indicts the first host's port or controller instead — keep the camera on the good port permanently.

Prevent it on the next install

Before install:

  • Camera on a root port, direct, with no docks or monitor passthroughs in the path — every hop adds a connector pair and a fresh place for EAGAIN.
  • Shielded USB 3 cable, 3 m or shorter passive; drag-chain rated wherever the cable moves.
  • Cable strain-relieved and routed through a drag chain, not pulled taut across the machine.

At commissioning:

  • lsusb -t shows 5000M for the camera; record the value in the station file.
  • Five-minute soak on the full production profile with no repeated EAGAIN and no kernel-log resets.
  • Per-controller payload summed and under about 200 MB/s wherever the controller is shared — the worked example's threshold.
  • Camera pinned by serial number or USB port in the SDK configuration.

In production:

  • Log EAGAIN counts per session and alert on growth; a rising count is the earliest sign of a wearing cable, long before frames drop.
  • Re-check the path after any rewiring — a replugged cable is the most common way a clean station goes bad.
  • Keep a spare USB 3 camera cable on the shelf; the cables finder lists the lengths and connector types.

More link and bandwidth diagnosis lives in the systems guides. If you are wiring the camera side of a new station, the configurator below starts at the cable and power extras so the link path is right before anything else is chosen.

Build the whole station

The configurator matches a camera, lens, light, light controller and cables to each other, step by step, and lists only parts that fit what you already picked.

Start with the cables and extras

Questions

Are a few control-transfer warnings at start-up a fault?

No. While the wrapper switches profiles and starts each sensor, the host queues a burst of control requests, and a handful of EAGAIN lines in the first seconds followed by silence is the normal signature. Judge the link by what happens after the streams settle. Warnings that continue every few hundred milliseconds during steady streaming, or that reappear when you add a stream, are the signature worth fixing. Use one clean minute of full-profile streaming as the pass criterion.

Does the EAGAIN flood mean the camera has outgrown the USB bandwidth?

Not in the arithmetic sense. The six-stream 640 × 480 at 30 fps profile carries about 64 MB/s, roughly one sixth of the roughly 400 MB/s a clean USB 3.x link sustains, so the streams fit with room to spare. EAGAIN reports a single request that could not be serviced at that instant — a degraded link busy retransmitting — not a bandwidth-overflow rejection. That is why cutting resolution rarely stops the flood while re-cabling does.

Why does the same warning repeat with index 768?

The index identifies which camera command failed, and it repeats because the wrapper polls the same periodic status read on schedule. One log can show several indexes — 300 early and 768 later, for example — because different queries hit the same wall as the link degrades. The indexes do not decode to separate faults: treat any recurring index as one unreachable control endpoint, fix the physical path, and every index goes quiet together.

How long can the USB cable to a depth camera be?

For a passive USB 3 cable, plan on 3 m as the reliable ceiling; the specification defines the Gen 1 cable assembly at that length, and a 60 MB/s stream leaves little margin beyond it. Longer runs need active or optical extensions, and those add electronics that can pass idle traffic yet fail under recording load. Keep the production cable passive, shielded and at or under 3 m, and test any extension under full load before trusting it.

When should I replace the camera instead of the cable?

Only after the camera fails its last chance: a root port, a known-good cable, no hub and a depth-only profile, then the same minimal profile on a second computer. Warnings repeating from the first frame on both machines point at the camera's USB transceiver or board, and replacement is justified. A clean run on the second PC clears the camera and convicts the first host's port or controller instead — move the camera to the good port and leave it there.